This page lists changes between PCLink versions.

Note: This version does not support connection to G4+ ECUs. A previous version of PCLink must be used to connect to older ECUs.

 

Version 6.19.105 - 10-02-21

·Made Wall Wetting Compensation hidden when fuel mode is off.

·Increased Overrun Ignition Trim max retard.

·Changed ST185 and ST205 Sample map trigger offset by 360deg.

 

Version 6.19.99 - 01-02-21

·Added Honda J30A4 trigger mode.

·Added ECUMaster Switch Board CAN files and help.

·Changed MX5 VVT mode to only show 1 bank.

·Changed default Subaru V7-10 Trigger 2 Type to Reluctor.

·Changed DI 1 Pull-up to On in the E36 sample maps.

·Fixed pressure calibrations not showing up for AN Temp inputs.

·Fixed Traction Disable Switch Labeling.

·Fixed Cruise Control On Input in Subaru mode issue.

·Fixed first character being lost when searching table axis runtimes.

·Fixed graph view being reset to 0 position on value change.

 

Version 6.19.65 - 25-11-20

·Added USB connection mode which improves connection reliability, this mode is also included as part of the Auto mode. USB Mode (or Auto) is the recommended Connection Port Option.

·Added a variety of fuel consumption runtime values.

·Added a virtual fuel tank function.

·Added fuel consumption calculation options to traditional fuel mode.

·Added E-Throttle error accumulators (TPS Main/Sub, APS Main/Sub, TPS/Target).

·Added V11 Subaru CAN Mode.

·Added Fuel trim settings to limits.

·Added a wall Wetting compensation setting.

·Added new Knock modes which normalise the engine noise.

·Added a knock 'Clear Now' option to clear all knock trim tables to 0.

·Allowed An Temp pins to be used by more functions (for example switched digital inputs and gear position inputs).

·Changed Speedo Max Freq to Max Speed, Changed Speedo Offset from Hz to Speed units. IF UPDATING FROM A PREVIOUS VERSION YOU WILL NEED TO CHECK THE MAX SPEED AND SPEEDO OFFSET SETTINGS.

·Changed Staged accel fuel setup, now has a single value to setup. IF UPDATING FROM A PREVIOUS VERSION AND USING STAGED FUEL YOU WILL NEED TO CHECK THE STAGED ACCEL SETTING.

·Added some new Bosch pressure and temperature sensor calibrations.

·Shortened a variety of runtime names and improved runtime searching to allow a variety of different search terms to find the same runtime.

·Added warning to Secondary extra staged mode stating that it is going to be removed. IF YOU ARE USING OR WANT TO USE THIS MODE PLEASE CONTACT TECH SUPPORT.

·Added 7Bar Map Sensor plug-in sample maps for the plug-in ECUs that have on-board MAP sensors.

·Fixed complimentary PWM Setup bug.

·Fixed trigger setup issue (most commonly seen when changing to an EVO trigger pattern).

 

Version 6.18.44 - 09-09-20

·Added Language Support for Japanese and Spanish (PCLink only, not Help Manual yet).

·Fixed Trigger Scope Layout not loading when being PCLink run from different directory.

 

Version 6.18.32 - 25-08-20

·Atom, Monsoon and Storm ECUs can now use all 45 GP Tables.

·Trigger Scope voltages now show 2dp.

·Fixed issue with loading loading Atom and Monsoon maps with German or French Windows setup.

 

Version 6.18.20 - 18-08-20

·Added OBD2 Functionality

·Added KMS Display, KMS UEGO, KMS EGT, DIY Auto Tune EGT and Microtech LTC Dash built in CAN streams.

·Added VW Mk5 Golf, Vauxhall Astra and Polaris RZR built in CAN modes.

·Added Latch settings for CAN DI inputs, they are located in Digital Inputs > CAN DI Latches.

·Added 16 CAN Auxiliaries which can be used for both switched and PWM functions (Act the same as an other Auxiliary Outputs but don't have a physical pin).

·Added voltage compensation On/Off settings to VVT, Boost and Idle Solenoid functions.

·Added Long Term Trim functionality to Closed Loop Lambda Auto Mode, refer here for information on how it works.

·Added PT Cruiser Trigger Modes.

·Added Knock Control and Analog Trigger Scope to V3 and newer Atom and Monsoon ECUs.

·Added import/export table to clipboard shortcuts (ctrl shift c and ctrl shift.

·Increased allowable Engine Speed ROC range for table axes.

·Increased Memo Size significantly to 56k of Unicode. The memo text can be found using by pressing ctrl + M and is stored as part of the basemap.

·Increased list of possible Table Axes to include all runtime values and statuses.

·Increased idle Min Clamp max value to 100.

·Changed CAN Analog displayed decimal places from 1 to 3.

·Fixed Table Import decimal places issue.

·Fixed issues with S, P, E and D shortcut keys.

·Fixed runtime selection view folder images.

·Fixed Mixture Map Transient Filters issue.

·Fixed CAN setup window Label/Status issue.

·Various improvements and fixes to ECU Logging.

Note: On upgrade to this firmware from an older firmware the ECU Statistics will be cleared.

 

Version 6.17.22 - 01-07-20

·Added Traction Control and Torque Management functions.

·Added GP Delays.

·Added more GP Tables.

·Added GP Output and GP PWM On Delay.

·Added new Starter Control lockouts (clutch and speed) and improved how it operates.

·Added Idle Base Position Table and Boost Wastegate %DC Table runtime values.

·Added Boost Control pressure source selection (allows tuning using a Boost pressure sensor instead of MAP).

·Added TPS Activation setting to Launch Control.

·Added Launch Control RPM Limit runtime value.

·Added Map Level trigger sync mode to Multi/Missing trigger mode.

·Added more Speedo Out speed source options.

·Changed Speedo Out sweep function to use Sweep Speed instead of Sweep Freq.

·Added CAN Bridge functionality.

·Added An Temp inputs to Analog Cruise Input options.

·Added CLL Target Error runtime values.

·Changed the first Trigger Arming table cell from 0 to 500rpm. IF UPDATING FROM A PREVIOUS VERSION AND USING RELUCTOR SENSORS CHECK YOUR 500RPM ARMING VOLTAGES.

·Added Motec E888 CAN stream.

·Improved PCLink default file path functionality.

·Made red cell markers disappear when saving offline.

·Fixed GP Output/PWM draw issues.

·Made Custom Calibration labels show up in calibration lists.

·Made CAN2 reserve DI 9&10 when using those pins.

·Added new layouts.

·Changed Knock defaults to have disable input Off and max Ignition trim/Fuel enrichment set to 0.

·Improved menu drawing making all menus and ECU connection load faster.

·Fixed DI using Aux status changing Aux function issue.

·Changed FP Speed min and max default values.

·Improved VANOS solenoid naming.

·Added inactive/active labels to vvt tables and improved label operation on other functions.

·Added JZX100 sample map.

·Added engine fan functionality to 350Z sample maps.

·Fixed CLL offline 3D table deallocation issue.

·Fixed 3 Wire ISC Antilag override table.

·Made Timers visible in Aux and DI menus.

·Made several fixes/improvements to the WRXV10 sample map

·Fixed Quick Trim form issues.

 

Version 6.16.64 - 17-04-20

·Added TGV functionality.

·Added JB-DET trigger mode.

·Added Thundercat trigger mode.

·Added Altezza plugin CAN streams to the install package.

·Added TGV functionality to the Subaru V10 sample map.

·Added Oil pump control table values to the Mazda RX7 S7-8 sample map.

·Increased max rpm limit value to 20,000rpm

·Shifted Subaru V7-10 Trigger offset by 360deg. IF UPDATING FROM A PREVIOUS VERSION AND USING THIS TRIGGER MODE YOU MUST CHECK YOUR OFFSET.

·Removed "vvt" from K6A trigger mode string (mode does vvt and non vvt).

·Stopped over/underflow errors from causing check engine lights and PCLink warnings.

·Fixed several exceptions which could cause PCLink to close unexpectedly.

·Fixed an offline rounding error on Table Axes.

 

Version 6.16.26 - 12-03-20

·Changed Accel Fuel Sens from a single value to a table. IF UPDATING FROM A PREVIOUS VERSION THE ACCEL ENRICHMENT SENS MUST BE SETUP.

·Added Cruise Control (available on Xtreme, Fury and Plug In ECUs).

·Added Modelled Multi Fuel.

·Added VANOS functionality to the VVT control.

·Added Closed Loop Fuel Pump Control.

·Added Active State setting to analogs being used as a digital input.

·Added a second speed limit.

·Added a PID Function for viewing the PID values of different control loops in real time.

·Increased Boost Control's maximum D Gain setting.

·Reduced Minimum Frequency output from 10Hz to 1Hz for settings and 0.6Hz for GP PWM Frequency tables.

·Added Knock control with Igntion retard and Fuel enrich functionality.

·Added Connection list Settings for Analog Inputs being used as DIs.

·Added Exhaust Pressure Analog Input.

·Added more Table Axis options and fixed Min/Max issues that some table axis options had.

·Trigger Scope made non modal (can change settings now while it is open).

·Double clicking on a pin function setting now takes you to the function using the pin (Pin function settings are found in the 'Input Pins' folders inside the Digital or Analog Inputs folders or the 'Output Pins' folder inside the Auxiliary Outputs folder).

·Added GP Rotary Switch Inputs (converts an Analog Voltage into a specified number of steps represented by an integer).

·Added Timer Labels

·Increased maximum number of VVT Teeth from 8 to 16.

·Increased Single Launch RPM's Launch RPM resolution from 100rpm to 1rpm.

·Added a Configurable MAP input filter.

·Added selectable Lambda Source to Closed Loop Lambda (CLL) and improved several other parts of CLL. IF UPDATING FROM A PREVIOUS VERSION AND USING CLL THE SOURCES WILL NEED TO BE SETUP CORRECTLY

·Added Lambda Target Error runtime.

·Made warmup enrichment able to be negative.

 

·Fixed an issue with the table axis insert button

·Fixed Logging lines on reconnect issue

·Fixed VVT PID custom/default selection issue

·Fixed Shift + Arrow selection resetting on Q/A press on Tables

·Fixed CAN Stream Load issue.

·Fixed Shift +/= and added Shift - shortcuts for adding or subtracting an amount from existing values.

 

Version 6.15.46 - 04-02-20

·Fixed an issue with Cal Table 6 axis units.

·Fixed an issue with VVT Tables not updating correctly when offline.

 

Version 6.15.41 - 10-01-20

·Added Closed Loop Boost Control GP Target Trim table.

·Fixed some PCLink help links.

·Added Virtual Auxiliaries to IC Spray output options.

·Increased CLL Startup Lockout max to 600s.

 

Version 6.15.36 - 19-12-19

·Improved how limit and fault code information is displayed.

·Fixed an issue with parameter search not displaying the first item.

 

Version 6.15.26 - 13-12-19

·Added Auxiliaries (including Fuel and Ignition) to the DI input options.

·Added Semi-Sequential Injection mode.

·Improved Math Block Help.

·Fixed offline Calibration Table rounding issue.

·Fixed offline logging frequency issue.

·Increased max number of user CAN parameters.

 

Version 6.15.18 - 11-12-19

Added sample base maps, fixed some help links, added some help, fixed some visibility.

 

Version 6.15.15 - 04-12-19

This is the first release version